Goodman and Amana filter sizes

On many Goodman and Amana gas furnaces the filter sits outside the cabinet, in a return grille, a side rack or the return duct. Goodman's manuals give a minimum size, not one fixed size. ASPT air handlers are different: they have a filter rack inside, and the cabinet letter in the model number tells you the size.

Does the model number settle it? Only partly. For its 80% furnaces, Goodman says filters don't ship with the furnace and the installer has to provide them.[1] The manual lists a minimum recommended filter size for each model code. It also says larger filters can be used, and that the filter can be in a central return instead.[1] So the filter in your house may be bigger than the table, or somewhere else. Start with the filter you have and use the tables to check it.

80% gas furnaces (GMS8, GMH8, GHS8, GME8, Amana AMEH8 and others)

Goodman's installation manual IO-446F covers the *M(H,S)8, GD(H,S)8, GHS8, GME8, Amana ADS(H,S)8 and AMEH8, and VMS8/VDS8 furnaces.[1] Its filter table is keyed by a short code from the middle of the model number. For example, the manual's blower tables list a model as GHS80805C***, and the code in the filter table is the 0805C part of it.[1] Find that same code on your furnace's rating label, then look it up below.

Goodman IO-446F, minimum recommended filter size, upflow/horizontal models[1]
Model codeSide returnBottom return
*0403A*one 16 x 25one 14 x 24
*0603A*one 16 x 25one 14 x 24
*0604B*one 16 x 25one 16 x 25
*0803B*one 16 x 25one 16 x 25
*0804B*one 16 x 25one 16 x 25
*0805C*one 16 x 25 (see note)one 16 x 25 (see note)
*0805D*two 16 x 25one 20 x 25
*1005C*two 16 x 25one 20 x 25
*1205D*two 16 x 25one 24 x 24
*1405D*two 16 x 25one 24 x 24

Note for *0805C*: if the furnace is paired with a cooling unit over 4 tons nominal, Goodman says to use two 16 x 25 filters with two side returns, or one 20 x 25 on the bottom return.[1] The table gives face sizes only and doesn't state a thickness.

Goodman IO-446F, minimum recommended filter size, downflow models[1]
Model codeTop return
*0403A*two 10 x 20, or one 14 x 25
*0603A*two 10 x 20, or one 14 x 25
*0804B*two 14 x 20, or one 16 x 25
*1005C*two 14 x 20, or one 20 x 25

Where the filter goes: in an upright install it can be in the central return grille, an external side rack (upflow), or the ductwork above a downflow furnace. In a horizontal install it goes in the central return grille or the return ductwork.[1] Goodman also says filters must meet UL900 (or CAN/ULC-S111 in Canada).[1]

1-inch vs 5-inch media on these furnaces

The same manual suggests a deep-pleated media filter of at least MERV 8 as an option, and warns against restrictive 1-inch filters with a pressure drop above 0.25 in. W.C.[1] It lists Goodman's Clean Comfort MERV 11 air cleaners, which use 5-1/4 inch media:[1]

Clean Comfort AM11 media air cleaners listed in IO-446F[1]
LocationMax heating airflowMedia dimensionsPart number (as listed)Family
Side or bottom return1200 CFM16 x 20 x 5-1/4 in.AM11-1620-5AM11-5
Side or bottom return1600 CFM16 x 25 x 5-1/4 in.AM11-1625-5AM11-5
Side or bottom return1600 CFM20 x 20 x 5-1/4 in.AM11-2020-5AM11-5
Side or bottom return2000 CFM20 x 25 x 5-1/4 in.AM11-2025-5AM11-5
Side or bottom return2 x 1600 CFMtwo 16 x 25 x 5-1/4 in.AM11-3225-5AM11-3225
Side return (right angle)2000 CFM20 x 25 x 5-1/4 in.AM11-2025-5RAAM11-5RA
Bottom return (platform)2000 CFM20 x 25 x 5-1/4 in.AM11-2832-5PPAM11-5PP
Bottom return (platform)2000 CFM20 x 25 x 5-1/4 in.AM11-2843-5PPAM11-5PP

The manual doesn't say whether these part numbers are for the whole cabinet or the replacement media. If you have one of these cabinets, read the label on the cabinet or the old media before you order.

ASPT air handlers: size by cabinet letter

For an ASPT air handler, look at the letter right after the two capacity digits in the model number. Goodman's spec sheet says that letter is the cabinet width: B is 17-1/2 in., C is 21 in. and D is 24-1/2 in.[2] The sheet lists one filter for each cabinet:

Goodman ASPT filters by chassis, spec sheet SS-GASPT (5/15)[2]
Chassis (cabinet letter)Cabinet widthGoodman filter partFilter size
B17-1/2 in.ALFH16201E16.0 x 20.0 in.
C21 in.ALFH1912201E19.5 x 20.0 in.
D24-1/2 in.ALFH20231E23.0 x 20.0 in.

So an ASPT model with C as the cabinet letter would take the 19.5 x 20 in. filter in this table. The sheet doesn't give a thickness, so measure the old filter's depth. A 19.5-inch width isn't a common store size, so it's worth checking the label on the old filter or ordering by the Goodman part number. The sheet also lists tool-less filter access as a feature.[2] Keep in mind that some installs filter the air at a return grille instead, even when the air handler has a rack.

Older Goodman furnaces: a filter area, not a size

Older Goodman manuals often don't name a filter size. The 2006 GMV8 two-stage manual, for example, gives a minimum filter area by furnace input. It says to put the filter in the return air duct outside the furnace cabinet, and that filters don't ship with the furnace.[3]

Goodman IO-315 (GMV8), minimum filter sizes by input[3]
Furnace inputDisposable filter (300 fpm)Permanent filter (600 fpm)
45M320 sq in.160 sq in.
68M483 sq in.241 sq in.
90M640 sq in.320 sq in.
115M800 sq in.400 sq in.
135M738 sq in.370 sq in.

To compare a filter with this table, multiply its length by its width. A 16 x 25 filter is 400 sq in., so on our arithmetic it meets every permanent-filter figure in the table, but only the 45M disposable figure. Goodman doesn't say whether to use nominal or actual dimensions, so treat this as a rough check. The manual also says that for 1800 CFM or more you need two side returns, or one side return plus a bottom return.[3]

Still not sure?

Go by the filter that's in there now, or measure the slot with our measuring guide. Our model and serial label guide shows where to read the model number, and MERV ratings explains the rating numbers. Other brands: Carrier, Trane.

Last checked 2026-11-19 against the documents listed under Sources.

Sources

Every number above links to the document it came from. We re-open each one and record the date in our source log.

  1. Installation Instructions for *M(H,S)8 / GD(H,S)8 / GHS8 / GME8 / ADS(H,S)8 / AMEH8 / VMS8 / VDS8 Gas Furnace (IO-446F, 07/2018), Goodman Manufacturing Company, L.P. (p. 22, Filters; p. 22, Minimum Recommended Filter Size, footnote ^; cover; pp. 22 and 39+, blower performance tables; p. 22, Upflow / Horizontal table; p. 22, footnote ¹; p. 22, Downflow table; p. 22, Upright Installations; p. 23, Horizontal Installations; p. 23; p. 23, air cleaner table). Last checked 2026-11-19.
  2. ASPT Series Multi-Position, Multi-Speed, ECM-Based Air Handler with Internal TXV, 1-1/2 to 5 Tons (SS-GASPT, 5/15), Goodman Manufacturing Company, L.P. (p. 2, Nomenclature; p. 12, Accessories: Filters; p. 1, features). Last checked 2026-11-19.
  3. Installation & Operating Instructions for GMV8 Gas Fired Warm Air Furnace, 2-Stage (IO-315, 6/06), Goodman Manufacturing Company, L.P. (p. 22, Filters; Circulation Air Filters; p. 22, Minimum Filter Sizes; p. 22, Filters). Last checked 2026-11-19.